Monthly Archives: December 2016

P5600 Series Connector with Surge Suppression

The Micro Protective Connectors are available in standard MINI, DIN 43650 Form “A” / ISO 4400, EN175301-803:2006 and Sub-Micro 8mm and 9.4mm. The Canfield Connector MPCs provide electrical controllers surge suppression against voltage spikes caused by the solenoids used on hydraulic and pneumatic solenoid valves.

See more at:  http://www.canfieldconnector.com/products/series/3058/p5600-din43650–surge-suppression

p5600_micro_protective_connector_photo


MCCR – Multiple Control Distribution

The Canfield Connector MCCR is a cable distribution connector which uses pass-through technology to allow control of multiple parallel or independent devices. Devised with double solenoids and solenoid valve manifolds in mind, the MCCR allows for simplified wiring and easy replacement of components in an automated, modular environment. The gasket-thin head fits between a single female connector and the associated male device with the DIN 43650 Form “A”, EN175301-803:2006 interface. Exiting from the MCCR head is a three conductor cable with ISO HT PG9 strain relief connector attached. Two available circuits allow for separate (independent) or parallel (simultaneous) control of the downstream device. The environment resistant quick connect style allows for plug and play designs in the factory that require modern hydraulic or pneumatic systems.

See more at:  http://www.canfieldconnector.com/products/series/3043/mccr-multiple-distribution-din-connector

And download our free Canfield Connector app any iOS or Anroid device.

OLYMPUS DIGITAL CAMERA


5JFAC – Fieldbus, Lighted, Suppressed

The Canfield Series 5JFAC all-molded DIN solenoid valve connector/gasket/cord offer a completely molded plug and play design that interfaces female ISO (DIN 43650 Form “A”), MINI and 9.4mm (Industry Standard) and 8mm Sub-Micro (DIN 43650 “C”) solenoid connections to 8mm or 12mm (round) circular connectors as shown on the following pages. Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility. The low profile “straight line” interface/cord configuration allows for installation in many limited space applications. The integrated gasket design boasts an IP67/NEMA 6 rating, is far better for environmental integrity than field wire versions and makes it impossible to lose the gasket! The 5FFAC and 5JFAC are the only molded valve connectors in the industry that feature bi-directional indicator lights and load suppression (not intended for UL 1449). UL and CSA versions are available as well. The Series 5JFAC is proudly Made in the U.S.A.

See more at:  http://www.canfieldconnector.com/products/series/3035/5jfac-molded-din-connector

And download our free Canfield Connector app on any iOS or Android device!

5jfac_fieldbus_molded_connector_photo


D5400 – Micro Solenoid Driver Power Converter

The Canfield Connector Series D5400 Micro Solenoid Driver is a NEMA 4 DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 and MINI type connector with a built in electronic circuit used to induce solenoid pull-in and reduce holding current. The time proven MSD has been designed into many applications where heat buildup occurs which reduces operating efficiency and life span of solenoid valves. The MSD has two main functions: one is to induce faster or stronger than usual response times at solenoid pull-in, the second is to reduce the net wattage of the solenoid during hold-in. The MSD drives the coil with a high input voltage for a fixed time period until the coil has shifted at which time the MSD reduces the holding voltage, which saves power, and the solenoid runs cool. The MSD is often used to replace low voltage power supplies where a 24 VDC solenoid valve can then be operated by 120 VAC. The Alternating current is rectified and the duty cycle reduced so as to operate the valve at proper voltage and wattage ranges. An additional advantage can be found when the MSD drops the holding voltage, which then reduces heat and current requirements.

See more at:  http://www.canfieldconnector.com/products/series/3038/d5400-micro-solenoid-driver-connector

And download our free Canfield Connector App on any iOS or Android device!

 

d5400_solenoid_driver_photo1


Canfield Connector Series 7000 – High Current Reed Switch

The Canfield Series 7000 proximity sensors are used to sense position on cylinders. They accommodate 2 to 8 inch bore tie rod cylinders or 3/4 to 4 inch round cylinders. This proven design is rugged yet cost effective. The Series 7000 boasts the largest number of custom circuits to match applications found in the market. Examples include; 1 or 4 Amp reed switches, normally open, normally closed or SPDT switch types, reed or electronic sensing elements in the same package style, and the industry’s first 120 VAC Hall sensor. Awide range of enclosures and connector options are available. To reduce stocking requirements, two clamp options feature a self-adjusting clamp for NFPA and other tie rod cylinders from 2 to 8 inch bore. Another clamp option features a band clamp from 3/4 to 4 inch round cylinders.

See more at:  http://www.canfieldconnector.com/products/series/3002/7000-reed-electronic-proximity-sensors

And download our free app on any iOS or Android device!

7000_sensor_photo