Category Archives: DIN 43650 Solenoid Driver

5JMSD – In-line Micro Solenoid Driver Molded Connectors

The Canfield Connector Series 5JMSD is a solenoid driver circuit (Coil Saver) tucked away in our all new in-line electronics package coupled with our 5J all-molded DIN solenoid valve connector/gasket/cord assembly for DIN 43650 Form A, Industry and Form C Solenoid Valve Connectors (EN 175301-803-2000 ). The integrated gasket design boasts an IP67/NEMA 6 rating and makes it impossible to lose the gasket. Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility. The Coil Saver enhances solenoid valve function as it lowers the wattage of solenoid operators of solenoid valves as it first applies a full voltage to ensure strong pull-in then drops the current when the solenoid magnetic circuit is most efficient and lowers wattage during long term energization or repeated cycles and lower RMS wattage. Both the in-line Coil Saver package and the 5J are fully encapsulated enclosures. This design allows for the Coil Saver to be isolated from the heat of the solenoid as well as installed upstream, away from the coil connector that is designed for this heat.  The DC voltage version is 46mm by 15mm cylinder and is IP68 fully sealed from dust and water ingress.  The in-line package can control input DC voltage and supplies PWM DC to the coil. The Series 5JMSD is Proudly Made in the U.S.A.

See more at:  http://www.canfieldconnector.com/products/series/3060/5jmsd—in-line-micro-solenoid-driver-molded-connectors

 

5jmsd_solenoid_driver_molded_connector_photor00


Canfield Connector Series 5950 – Micro Proportional Driver

A Micro Proportional Driver provides accurate control of hydraulic and pneumatic proportional solenoid valves used in mobile construction equipment and industrial processes. The MPD can control the flow of air or liquid linearly at a setting from 0.10-20 seconds. One example of use would be in a paint system. The MPD allows a solenoid to oscillate, significantly reducing system shock and wear commonly found in non-oscillation digital valve systems. The micro proportional driver is a compact electronic circuit built into an environment-resistant miniaturized enclosure. The circuit features control of proportional solenoids and operators. Functions include minimum and maximum current limiting, control signals from 0-10V or 0-20 mA (with a step function at 0.2V or 0.4 mA included for minimum current), a 0.1-20 sec. linear ramp up/ramp down adjustment and output current proportional to input command signal. This unit incorporates the DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connector male and female interface. The unit is mounted by use of a single mounting screw, DIN connector and two gaskets. Built to meet NEMA 4 environment standards, the MPD is made from engineered polymers for resistance to harsh chemicals and ingress of water or foreign substances. Adjustments are made on the top surface of the unit. The unit can control any proportional solenoid valve operation within the values specified below using variable pulse width modulation.

 

See more at:  http://www.canfieldconnector.com/products/series/3026/5950

 

5950_proportional_driver_photo


5JMSD – In-line Micro Solenoid Driver Molded Connectors

The Canfield Connector Series 5JMSD is a solenoid driver circuit (Coil Saver) tucked away in our all new in-line electronics package coupled with our 5J all-molded DIN solenoid valve connector/gasket/cord assembly for DIN 43650 Form A, Industry and Form C Solenoid Valve Connectors (EN 175301-803-2000 ). The integrated gasket design boasts an IP67/NEMA 6 rating and makes it impossible to lose the gasket. Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility. The Coil Saver enhances solenoid valve function as it lowers the wattage of solenoid operators of solenoid valves as it first applies a full voltage to ensure strong pull-in then drops the current when the solenoid magnetic circuit is most efficient and lowers wattage during long term energization or repeated cycles and lower RMS wattage. Both the in-line Coil Saver package and the 5J are fully encapsulated enclosures. This design allows for the Coil Saver to be isolated from the heat of the solenoid as well as installed upstream, away from the coil connector that is designed for this heat.  The DC voltage version is 1.83 by 0.60 cylinder and is IP68 fully sealed from dust and water ingress.  The in-line package can control input DC voltage and supplies PWM DC to the coil. The Series 5JMSD is Proudly Made in the U.S.A.

http://www.canfieldconnector.com/products/series/3060/5jmsd—in-line-micro-solenoid-driver-molded-connectors