Tag Archives: DIN 43650 Form “A” for Molding

5JMSD – In-line Micro Solenoid Driver Molded Connectors

The Canfield Connector Series 5JMSD is a solenoid driver circuit (Coil Saver) tucked away in our all new in-line electronics package coupled with our 5J all-molded DIN solenoid valve connector/gasket/cord assembly for DIN 43650 Form A, Industry and Form C Solenoid Valve Connectors (EN 175301-803-2000 ). The integrated gasket design boasts an IP67/NEMA 6 rating and makes it impossible to lose the gasket. Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility. The Coil Saver enhances solenoid valve function as it lowers the wattage of solenoid operators of solenoid valves as it first applies a full voltage to ensure strong pull-in then drops the current when the solenoid magnetic circuit is most efficient and lowers wattage during long term energization or repeated cycles and lower RMS wattage. Both the in-line Coil Saver package and the 5J are fully encapsulated enclosures. This design allows for the Coil Saver to be isolated from the heat of the solenoid as well as installed upstream, away from the coil connector that is designed for this heat.  The DC voltage version is 46mm by 15mm cylinder and is IP68 fully sealed from dust and water ingress.  The in-line package can control input DC voltage and supplies PWM DC to the coil. The Series 5JMSD is Proudly Made in the U.S.A.

See more at:  http://www.canfieldconnector.com/products/series/3060/5jmsd—in-line-micro-solenoid-driver-molded-connectors

 

5jmsd_solenoid_driver_molded_connector_photor00


Solenoid Valve Connector Series 5F

The Canfield Series 5F all-molded DIN solenoid valve connector/gasket/cord assembly offers a completely molded design that is far better for environmental integrity than field wire versions. Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility. The low profile “straight-line” interface/cord configuration allows for installation in many limited space applications. The integrated gasket design boasts an IP67/NEMA 6 rating and makes it impossible to lose the gasket. The 5F and 5J are the only molded valve connectors in the industry that feature a HARD USAGE cord as a standard option in any length required, bi-directional indicator lights, and load suppression (not intended for UL 1449). UL and CSA versions are available as well. Canfield offers any version of the 5F connector with special wires including high flex, media compatible wire, special use wire, high temperature wire on request. The Series 5F is Proudly Made in the U.S.A.

Watch our YouTube video to see how they work! https://www.youtube.com/watch?v=Q3b4_ZP07yQ

See more at:  http://www.canfieldconnector.com/products/series/3001/5f-molded-din-connectors

And download our free app on any iOS or Android device!

5f_molded_connector_photo


Canfield Connector Series 5JR-Rectified, Lighted, Suppressed

The Canfield Series 5JR solenoid valve connectors incorporate a full-wave bridge rectifier inside a fully molded connector.  The 5JR converts alternating current to direct current reducing coil burnout due to valve sticking.  Also, direct current eliminates AC “hum” inherent to alternating current.  Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility.  The low profile 90° interface/cord configuration allows for installation in many limited space applications.  The integrated gasket design boasts an IP67/NEMA 6 rating and makes it impossible to lose the gasket!  Features load suppression (not intended for UL 1449).  The Series 5JR is Proudly Made in the U.S.A.

See more at:  http://www.canfieldconnector.com/products/series/3037/5jr-molded-din-connector

 

5jr_molded_connector_photo


iLW – Interposed Lighted Wafer Indicator Light

The Canfield Connector Interposed Lighted Wafer is an electronic, state of the art lighting module designed to install between a DIN (DIN 43650) type coil and the mating connector. Utilizing SMT (Surface Mount Technology), the iLW’s ultra-thin design and high luminescence Gallium Arsenide LEDs enable the lighted wafer to retrofit existing applications or to be used in conjunction with unlighted connectors. Designed to “sandwich” between the connector and the coil, the iLW seals from dust and moisture. The iLW can be installed several times without degradation of the contact surfaces and is not polarity dependent.

See more at: http://www.canfieldconnector.com/products/series/3041/ilw-electronic-lighted-din-connector-module

ilw_lighted_wafer_connector_photo


Canfield Series 5FFAC Molded Connectors

The Canfield Series 5FFAC all-molded DIN solenoid valve connector/gasket/cord offer a completely molded plug and play design that interfaces female ISO (DIN 43650 Form “A”), MINI and 9.4mm (Industry Standard) and 8mm Sub-Micro (DIN 43650 “C”) solenoid connections to 8mm or 12mm (round) circular connectors.  Made from rugged yet flexible polyurethane, the connector housing boasts high durability factors and application versatility. The low profile “straight line” interface/cord configuration allows for installation in many limited space applications. The integrated gasket design boasts an IP67/NEMA 6 rating, is far better for environmental integrity than field wire versions and makes it impossible to lose the gasket! The 5FFAC and 5JFAC are the only molded valve connectors in the industry that feature bi-directional indicator lights and load suppression (not intended for UL 1449). UL and CSA versions are available as well. The Series 5FFAC is proudly Made in the U.S.A.

5ffac_fieldbus_molded_connector_photo

See more at: http://www.canfieldconnector.com/products/series/3034/5ffac-molded-din-connector


Need Canfield Connector Literature?

Download the full catalog at http://www.canfieldconnector.com/DownloadCatalogs.aspx


M5 Male DIN 43650 form A for molding

DIN 43650 Form A for Molding
M5_DIN 43650 Form A for Molding

 

 

 

 

 

 

 

 

 

This male DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 connector can be integrated in tooling to provide a cost effective quick connect electrical interface.  The P10020 is designed to mate with Series 5000 or other DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 female electrical connectors.

Features:

  • Rugged design, Made in USA
  • DIN 43650 Form “A” / ISO 4400, EN175301-803:2000 configuration
  • 2+ or 3+ Ground versions
  • 250V AC/DC max.
  • Glass Fiber Reinforced Nylon
  • 10 Amps max. rating
  • Temp. rating -40° to +125° C